Service für Gigaset DX800A

Please check, whether the Bluetooth accessory supports one of the given protocols, which are supported by the Gigaset:

• headset profile (for Bluetooth headsets)
• handsfree profile (for Bluetooth headsets)
• serial port profile (for PC connection)
• OBEX (send/receive vCards)

When the Bluetooth accessory was installed already, please delete the registration from the handset:

• Bluetooth Menu
• Known Devices
• Select the accessory, e.g. a headset
• Options
• Delete Entry

If it is again not possible to register the accessory to the base station, please check, whether the accessory supports a reset-function, and execute it. Please pay attention that perhaps previous settings will be deleted in the accessory.

If you would like to use a headset already registered to another device (e.g., to a mobile phone) with your desktop phone, please deactivate this connection before you start the registration process.

• Connecting Bluetooth headsets
• Exchanging address book entries (as VCards) with another Bluetooth device (e.g. mobile, PDA)
• Synchronizing contacts from the PC to the address book of the Gigaset and download of ringer-tones or pictures using the QuickSync Software
• Link2Mobile
  

Prerequisite: Bluetooth is activated; a connection has been established between the Bluetooth headset and the handset.

• Press the talk key on the headset or the function key Headset on the desktop phone.
• Only press the talk key on the headset when the headset rings; this can take up to 5 seconds. 

You can program the function key on the

desktop phone manually.

For further details about your headset, see

the accompanying user guide.

Prerequisite: Bluetooth is activated; a connection has been established between the Bluetooth headset and the desktop phone.

• Press the talk key on the headset.

It may take up to 5 seconds to establish a connection to the desktop phone.
For more information, see the headset's user guide.

You can program the six function keys on the

right-hand side of the desktop phone and

the display keys (in idle status). You can

assign a phone number (quick dial) or a

desktop phone function to each of these

keys and change the assignment.

The number is then dialled or the function

started by simply pressing a key.

To program the function "headset" to one of the six function keys, press and hold the display/function key

until a list of possible key assignments is

displayed. Select the function "headset" in the list and press OK. 

Before you can use your Bluetooth devices, you must first activate Bluetooth and then
register the devices to the desktop phone. To use the phone numbers, dialing codes
(country and area code) must be stored on the desktop phone.

Activating/deactivating Bluetooth mode

• Menu
• Bluetooth
• Activation
• Select and press OK to activate or deactivate Bluetooth mode

When the desktop phone is in idle status, the icon in the header indicates that Bluetooth mode is activated. As soon as Bluetooth is activated, your desktop phone is visible to all Bluetooth devices
in the receiving range and can communicate with all of the devices included in the Known Devices list.

Registering Bluetooth devices
The distance between the desktop phone in Bluetooth mode and the activated Bluetooth device (headset or data device) should be no more than 10 m.

• Menu
• Bluetooth
• Search for Headset / Search for Mobile phone / Search for Data Device

The search can take up to 30 seconds. Once the device has been found, its name or address is shown on the display.

• Press the display key “Options”.
• Trust Device
• Select and press OK.
• Enter the PIN of the Bluetooth device to be registered and press OK.

Generally you can enter a PIN of your choice for a data device. Subsequently, you must enter this PIN in the data device, too. Enter the preset PIN for the headset (usually:0000). For further information, please refer to the headset user guide. The device is saved in the list of known devices.

Please note:

You can operate headsets on your handset that have the headset or handsfree profile. If both profiles are available, the handsfree profile is used to communicate.

It can take up to five seconds to establish a connection between your desktop phone and a Bluetooth headset. This applies both when a call is accepted using the headset or transferred to the headset, and when a number is dialed from the headset.

If you would like to use a headset already registered to another device (e.g., to a mobile phone) with your desktop phone, please deactivate this connection before you start the registration process.
The known devices list can only contain one Bluetooth headset. If you register a second headset, the first one is deleted from the list.
If the list already contains six entries, the last device to be entered is deleted during the subsequent registration process.
Exception: The headset entry is only overwritten by a new headset and a headset only overwrites the headset entry.

The Gigaset supports 2 Bluetooth connections

in parallel (Bluetooth headset and OBEX transfer/or PC connection)

You

can register 1 Bluetooth headset to the Gigaset. You can also register

up to 5 data devices (e.g. PC, PDA, mobile phone) to send and receive

directory entries as vCards or exchange data with the computer.

The connection between your PC and the Gigaset depends on your Bluetooth device at the PC.

To get a connection to the Gigaset it is necessary to activate the Bluetooth function at the base station.

Then start your Bluetooth software at your PC and search for new Bluetooth devices. The Gigaset will be shown, preconditioned it is in the radio radius of max. 10 meters to your PC.

After the PC has found the Gigaset you have to enter a security code. As a rule you get several possibilities for the security code. Please select the on which offers you to enter the code manually. Then enter a code, like 0000. Right now a window appears in the base station which prompts you to enter the code. Please enter here the same code as you selected before: 0000

The pairing now has finished.

Yes, it is possible to dial the last dialed number from redial list (re-dialling).

Please note: The Bluetooth headset must also support this functionality. For further information,

please refer to the headset user guide.

If a Bluetooth headset is registered and a corded heaset is plugged in, the corded headset cannot be used.

Please deregister other devices which were possibly registered to the Gigaset before.

• Bluetooth Menu
• Known Devices
• Select the accessory, e.g. a headset
• Options
• Delete Entry

If it is again not possible to register the accessory to the Gigaset, please check, whether the accessory supports a reset-function, and execute it. Please pay attention that perhaps previous settings will be deleted in the accessory.

Whether Bluetooth® devices can communication with each other is a profile question. It is important that they support and use the same Bluetooth® profile for different functions.

The Gigaset supports the Headset Profile and Handsfree Bluetooth profil for communication with a headset. 

You can operate headsets on your handset that have the Headset or Handsfree profile. If both profiles are available, the handsfree profile is used to communicate.

Known BT-Headsets that do not work correctly with S810H, S820H and SL400H:
- Jabra Wave BT 3.0 (100-93050000-60)

Whether

Bluetooth® devices can communication with each other is a profile

question. It is important that they support and use the same Bluetooth®

profile for different functions.

The Gigaset support the following Bluetooth® profiles:

• Serial Port Profile (SPP) for data communication with a PC.
• Headset Profile and Handsfree profil for communication with a headset.
• OBject EXchange Profile (OBEX) for the transfer of address book entries (vCards).

You will find a description how to connect a doorline to the FAX port of the Gigaset DX800A in the User guide extension.

Gigaset DX800A all-in-one User guide extension V02 en (PDF)

The following problems may occur when connecting to the incoming e-mail server. The messages are displayed in the display for a few seconds.

Prerequisites: Your base is connected to the Internet.

E-mail server inaccessible

The connection to the incoming e-mail server could not be established. This may have the following causes:

• Incorrect entry for the name of the incoming e-mail server. Please note that the server has to use the POP3 protocol(IMAP protocol or a secure SSL/TLS connection to a POP3S server is not supported)
• Temporary problems with the incoming e-mail server (server is down or is not connected to the Internet).

Solution:

• Check the e-mail settings in the Web configurator.
• Try again later.

Currently not possible

The resources your phone requires to make the connection are busy, e.g.:

• The permitted number of VoIP connections has already been reached.
• One of the registered handsets is currently connected to the incoming e-mail server.
• Incorrect entry for the name of the incoming e-mail server. Please note that the server has to use the POP3 protocol(IMAP protocol or a secure SSL/TLS connection to a POP3S server is not supported)

Solution:

• Try again later.
• Check the e-mail settings in the Web configurator

Login failed

Error when logging in to the incoming e-mail server. This may have the following cause:

• The permitted number of VoIP connections has already been reached.
• Incorrect entries for name of incoming e-mail server, user name and/or password. Please note that the server has to use the POP3 protocol(IMAP protocol or a secure SSL/TLS connection to a POP3S server is not supported)

Solution:

• Check e-mail settings in the Web configurator.

Mailbox settings incomplete

• Incomplete entries for name of incoming e-mail server, user name and/or password. Please note that the server has to use the POP3 protocol(IMAP protocol or a secure SSL/TLS connection to a POP3S server is not supported)

Solution

• Check/add to e-mail settings

No, the device connects the server and the mails can be read online. You can delete the Mails on the server with an separate procedure.

No, IMAP is not supported.

Your phone will notify you when new e-mail messages have been received on your incoming e-mail server. You can set your phone to periodically connect to your incoming e-mail server and check whether you have new e-mail. Any new e-mail messages that have been received are displayed on the base and on all Gigaset handsets that have been registered:

you will hear an advisory tone, the message key will flash and the message icon will be displayed in the idle display.

You can use your phone to connect to the incoming e-mail server and display the sender, date and time of receipt, subject and text (abbreviated if necessary) for every e-mail message in the incoming mail list.

Prerequisites:

• Your base is connected to the Internet.
• You have set up an e-mail account with an ISP.
• The incoming e-mail server uses the POP3 protocol (secure SSL/TLS connections to POP3S server are not supported).
• You have stored the name of the incoming e-mail server and your personal access data (account name, password) in the phone via the Web configurator.

Do the following steps to configure the e-mail notification via the Web configurator:

• Open the Settings - E-Mail in the Web configurator
• Enter the user name(account name) agreed with the internet provider (max. 74 characters) in the Authentication Name field
• Enter the password agreed with the provider for accessing the incoming e-mail server (max. 32 charaters; case sensitive) in the Authentication password field.
• Enter the name of the incoming e-mail server(POP3 server) (max. 74 characters) in the POP3 Server field. Example: pop.theserver.com.
• From the Check for new e-mail list select the time interval at which your phone should check if the new messages have arrived in your incoming e-mail server. Select Never to deactivate the promt. Select one of the other values to activate the promt for new e-mail messages.
• Select the Set button to save the settings in your phone.

120 characters

No, only one e-mail notification is possible.

Only e-Mail notification is possible.

Due to the new functions on the FAX port (FXS port / Int 8) with the version 093 (DX800A) and version 094 (DX600) you have to set up the FXS port after the update.

• Open menu
• Select "Settings"
• Select "System"
• Select "FXS-Port"
• Select Mode "Telephony/Fax"
• Confirm the settings with "Save"
  

After that you have set up the receive connections for the internal user Int8 again:

• Open Mneu
• Select "Settings"
• Select "Telephony"
• Select "Receive connection"
• Select Internal user 8
• Select the receive MSN(s) for Int 8
  
• Confirm the settings with "Save"
  

• Please check if the Fax port is active (Menu -> Settings -> System -> Fax Port)

• If you still can't send out faxes with activated Fax port, you have to switch off the dial-tone-detection of your fax. Please have a look into your manual from the fax machine to change these setting.
  

• Please check if the Fax port is active (Menu -> Settings -> System -> Fax Port)

• If the connected fax machine is a multi-function device please select the setting "fax-mode" and not "multi-function-mode". Please have a look into your manual from the fax machine to change these setting.

• Update your Gigaset to the newest firmware (Menu -> Settings -> System -> Firmware-Update).
  

If you own a Gigaset IP Base / Gigaset GO-Box and it is connected to your router/modem via LAN cable, please check the following steps:

• Use the LAN cable from the Gigaset packaging.
• Connect the Gigaset base via LAN cable to the router (e.g. to LAN1). Please note: The blue LED of the Gigaset base must flash!
• Please make sure that your internet connection is working. A working internet connection is required for telephony.
• Please make sure that your telephony data (internet telephone numbers, provider-profile, …) is only entered in Gigaset base. If telephony data is also entered in the router, please delete it! Please note: Often an error message is displayed when telephony data is entered wrong (e.g. “Provider registration is not possible” or “Server not available”.
• Furthermore each handset must be associated with the correct send connection and receive connection. Please check this by holding down the green button and selecting the first IP connection. Afterwards you have to press the green button briefly and dial a telephone number. In case of an error message such as "Connection is not established", please contact your provider.
• If either you can only hear your call partner or your call partner can only hear you, change the STUN-settings in the web configurator of the base (activate if disabled and vice versa). If a call is possible afterwards, configure the send connection for all registered handsets.
• If no call is possible after that, you can check your VoIP-line by echo test via Gigaset.net. The echo-service is available at the following telephone number: 12345#9 . After an announcement the echo-service will send back(directly as an echo) the voice data received from you. Please contact your provider if the echo test is okay.

If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:

• Use the phone cable from the Gigaset packaging.
• If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
• Connect the cable to the router`s phone jack / phone port / FON port.
• Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
• Please make sure that your internet connection is working.

If the problem persists, please contact your provider.

Due to the new functions on the FAX port (FXS port / Int 8) with the version 093 (DX800A) and version 094 (DX600) you have to set up the FXS port after the update.

• Open menu
• Select "Settings"
• Select "System"
• Select "FXS-Port"
• Select Mode "Telephony/Fax"
• Confirm the settings with "Save"
  

After that you have set up the receive connections for the internal user Int8 again:

• Open Mneu
• Select "Settings"
• Select "Telephony"
• Select "Receive connection"
• Select Internal user 8
• Select the receive MSN(s) for Int 8
  
• Confirm the settings with "Save"
  

Default data server “gigaset.com/chagall” doesn’t work anymore and must be replaced with “profile.gigaset.net/device” over WEB UI under Settings - Management – Firmware Update.

No. Both, caller and callee have to be in the Gigaset.net network.

Press the Control key slightly longer then when accessing your directory. Scroll down to Gigaset.net by using the Control key and acknowledge by pressing the right-sided Display key.

If you use a other handset there are three ways to enter the Gigaset.net directory:

• Enter your directory and select Gigaset.net.
• Dial 1188#9 and acknowledge by pressing the Talk key (green phone receiver symbol).
• You can program the fast access function of key 1 for entering the Gigaset.net. For details on how to program the fast access function, please refer to your Gigaset’s manual.

Depending on your Gigaset, there are two different ways to access your account data:

• Dial 1188#9 and acknowledge by pressing the Talk key. Enter Options by pressing the right-sided Display key. Scroll down to Own details by using the Control key and acknowledge by pressing the right-sided Display key.
• Dial 1188#9 and acknowledge by pressing the Talk key. Search the Gigaset.net directory for a name. Enter Options by pressing the right-sided Display key. Scroll down to your own data by using the Control key and acknowledge by pressing the right-sided Display key. Your Gigaset.net number and name will be shown. 

An echo service is available for you to check

your VoIP connection.

The echo service is available in six languages:

• 12341#9 (English)
• 12342#9 (Dutch)
• 12343#9 (Italian)
• 12344#9 (French)
• 12345#9 (German)
• 12346#9 (Spanish)

After an announcement, the echo service

immediately sends back the voice data you

have received in the form of an echo.

Yes. Calls via Gigaset.net are free of charge. Yet, if you do not have flat rate Internet access, costs will incur.

Each Gigaset VoIP has an unalterable Gigaset.net number. If your phone just has to be repaired, you can keep both, nickname and number. But if your phone has to be swapped, you will get a new number and therefore have to choose a new nickname.

With Gigaset.net you can make free of charge phone calls to other Gigaset.net members all over the globe via the Internet. To use the service you do not have to register with a VoIP provider or make any additional settings. You just have to plug in your phone’s mains adapter and to establish a connection to the Internet. To activate the service, search the Gigaset.net directory for any nickname. Calls via Gigaset.net are free of charge. Yet, if you do not have flat rate Internet access, costs will incur.

If your Gigaset.net account has been idle for more than six weeks, it will be deactivated automatically. To reactivate your account, you have three options:

• Search the Gigaset.net directory.
• Make a call via Gigaset.net (call a phone number that ends with #9).
• Reactivate your account via web-interface.

The configuration can be done with the Web Configurator. Under “Settings” – “Telephony” – “Number assignment” you can configure the send – and receive numbers.

Prerequisites: A standard Web browser is installed on the PC e.g., Internet Explorer version 6.0 or higher, or Firefox version 1.0.4 or higher. The phone and PC are directly connected with each other via a router. The settings of any existing firewall installed on your PC allow the PC and phone to communicate with each other.

There are two ways of connecting your PC to the Web configurator on the Gigaset:

1. Via the phone's IP address in the local network

Establish the current IP address of the phone. It is displayed when you open the following menu:

• Menu-Settings-System-Local Network (enter PIN)

Your phone's IP address can change if you have activated dynamic IP address Assignment

• Launch the Web browser on your PC.

• Enter http:// and the telephone's current IP address (for example:http://192.168.2.2) into the address field of the Web browser.

• Press the return key.

A connection is established to the phone's Web configurator.

Warning:
If one of the four parts of the IP address contains leading zeros (e.g., 002), these zeros must not be entered in the Web browser address field. Otherwise, the Web browser will not be able to establish a connection to the Web configurator.
Example: The IP address 192.168.002.002 is displayed on the phone. 192.168.2.2 should be entered in the address field.

2. Via the Gigaset configuration service, if the phone and PC are connected to the Internet

Prerequisite: Your PC and phone are connected to the Internet.

• Launch the Web browser on your PC.
• Enter one of the following URLs into the Web browser's address field:

www.gigaset-config.com
www.gigaset-device.com

• Press the return key.

You will receive a message stating that the connection has been forwarded to phone.
If several Gigaset phones can be reached via your Internet connection, you are asked which of these phones you would like to be connected to.
After successfully forwarding the connection, the Web configurator's Login page is displayed in the Web browser.

Please note:
The connection between the PC and the Web configurator is a local connection (LAN connection). The Internet is only accessed to establish the connection.

It depends on the type of compression. The bandwidth for Voice over IP is between 12 and 80 KBit/s. Please note that these values are theoretical. For practice: As much bandwidth as possible.

The default setting for your phone only allows you to access your phone's Web configurator via a PC that is in the same local network as your phone. The subnet mask of the PC must match that of the phone. You can also allow access from PCs in other networks:

• Open the Web configurator
• Go to "Settings" - "IP Configuration"
• Show Advanced Settings
• Enable the option "Allow access from other networks"

Warning: Authorising access from other networks increases the risk of unauthorised access. It is therefore recommended that you disable remote access if you no longer require it.

Please note: The Web configurator services can only be accessed from other networks if your router passes on the service requests from "outside" to port 80 (the default port) of the phone. Make sure you read the user manual for your router. To establish a connection, the public IP address or the DNS name of the router and, where applicable, the port number on the router must be indicated in the Web browser of the remote PC.

In case of using fix IP addresses, you have to configure additional setting via the Web Configuration.
Please open in the Web configuration the option “Settings” – “IP-Configuration”. The IP address and the Subnet Mask must fit to your Routers IP range. For the Default Gateway and DNS Server you should enter the Routers IP address.

Default data server “gigaset.com/chagall” doesn’t work anymore and must be replaced with “profile.gigaset.net/device” over WEB UI under Settings - Management – Firmware Update.

The following voice codecs are supported by your phone:

G.722

Excellent voice quality. The broadband speech codec G.722 works at the same

bit rate as G.711 (64 kbit/s per speech connection) but with a higher sampling

rate. This allows higher frequencies to be played back. The speech tone is therefore

clearer and better than for the other codecs (High Definition Sound Performance).

G.711 a law / G.711 μ law

Excellent voice quality (comparable with ISDN). The necessary bandwidth is

64 kbit/s per voice connection.

G.726

Good voice quality (inferior to that with G.711 but better than with G.729).

Your phone supports G726 with a transmission rate of 32 kbit/s per voice

connection.

G.729

Average voice quality. The necessary bandwidth is less than or equal to 8 kbit/s

per voice connection.

To save additional bandwidth and transmission capacity, on VoIP connections

that use the G.729 codec you can suppress the transmission of voice packets in

pauses ("Silence Suppression"). Instead of the background noises in your environment,

your caller then hears a synthetic noise generated in the receiver

(option: Enable Annex B for codec G.729).

Since version 02081 the device synchronized the time after every new system start or every new time configuration or in the night between 0:00 and 3:30 o’clock automatically. The timeserver „europe.pool.ntp.org“ is preconfigured. It is possible to overwrite the default timeserver with an own entry. The functionality can be switched off with the Web Configurator.

You can read out the IP address from the base via the base menu:

• Press Menu-key
• Enter 9 8 5
  
  • IP Address Type
  • IP address
  • Subnet Mask
  • Default Gateway
  • DNS Server
    

It depends on the type of compression. The bandwidth for Voice over IP is between 12 and 80 KBit/s. Please note that these values are theoretical. For practice: As much bandwidth as possible.

The default setting for your phone only allows you to access your phone's Web configurator via a PC that is in the same local network as your phone. The subnet mask of the PC must match that of the phone. You can also allow access from PCs in other networks:

• Open the Web configurator
• Go to "Settings" - "IP Configuration"
• Show Advanced Settings
• Enable the option "Allow access from other networks"

Warning: Authorising access from other networks increases the risk of unauthorised access. It is therefore recommended that you disable remote access if you no longer require it.

Please note: The Web configurator services can only be accessed from other networks if your router passes on the service requests from "outside" to port 80 (the default port) of the phone. Make sure you read the user manual for your router. To establish a connection, the public IP address or the DNS name of the router and, where applicable, the port number on the router must be indicated in the Web browser of the remote PC.

In case of using fix IP addresses, you have to configure additional setting via the Web Configuration.
Please open in the Web configuration the option “Settings” – “IP-Configuration”. The IP address and the Subnet Mask must fit to your Routers IP range. For the Default Gateway and DNS Server you should enter the Routers IP address.

The following voice codecs are supported by your phone:

G.722

Excellent voice quality. The broadband speech codec G.722 works at the same

bit rate as G.711 (64 kbit/s per speech connection) but with a higher sampling

rate. This allows higher frequencies to be played back. The speech tone is therefore

clearer and better than for the other codecs (High Definition Sound Performance).

G.711 a law / G.711 μ law

Excellent voice quality (comparable with ISDN). The necessary bandwidth is

64 kbit/s per voice connection.

G.726

Good voice quality (inferior to that with G.711 but better than with G.729).

Your phone supports G726 with a transmission rate of 32 kbit/s per voice

connection.

G.729

Average voice quality. The necessary bandwidth is less than or equal to 8 kbit/s

per voice connection.

To save additional bandwidth and transmission capacity, on VoIP connections

that use the G.729 codec you can suppress the transmission of voice packets in

pauses ("Silence Suppression"). Instead of the background noises in your environment,

your caller then hears a synthetic noise generated in the receiver

(option: Enable Annex B for codec G.729).

You can use your desktop phone to retrieve online content from the Internet i.e., request info services that are provided specifically for the telephone. The info services available are constantly updated. A default selection has already been made, but you can change these settings and add new services.

• Open the Web configurator page Menu-Settings-Services-Info Services on the PC

• Click the link gigaset.net/myaccount

Or:

• Enter the following address in the address field of your PC's Web browser: www.gigaset.net

Enter your Gigaset.net user ID and password on the Gigaset.net page. You will find your user ID and password on the Web configurator page specified above.

In both cases, a Web page is opened on which you can compile your info services.

You can configure your base to display a customized information feed (e.g., weather

reports, newsfeeds) in the device's idle display.

To do so, you must enable the Info Ticker or the Info Services screensaver on your base.

Info Services screensaver:

• Open Menu-Settings-Display-Screensaver

The current setting is displayed.

You can enter data in the following fields:

Activation:

• Select On (screensaver is displayed) or Off (no screensaver).

Selection:

• Select Info Services and press OK.
• Press the display key Save.

Info Ticker:

• Open Menu-Settings-Display-Info Ticker
• Activate the Info Ticker

The ticker starts as soon as the telephone changes to idle status. If, however, a message is shown in the idle display, the information ticker is not displayed.

The default InfoService is the weather report. You can select the information to be displayed

via the gigaset.net server.

• Open the Web configurator page Menu-Settings-Services-Info Services on the PC.
• Click the link www.gigaset.net/myaccount

Or:

• Enter the following address in the address field of your PC's Web browser: www.gigaset.net/myaccount
  
  Enter your Gigaset.net user ID and password on the Gigaset.net page. You will find your user ID and password on the Web configurator page specified above.

In both cases, a Web page is opened on which you can compile your info services.

Open Menu-Additional Features-Info Centre at the Gigaset.

Your info centre menu i.e., a list of available info services is displayed.

You can navigate between the info services.

Select the info service and press OK.

A connection is automatically established between the base in Bluetooth mode and the activated mobile in range:

• If a call arrives via the mobile's GSM connection
• If you attempt to make a call on the base via the GSM connection

If Bluetooth mode is deactivated on the base:

• Open the list of known devices.
• Select the activated mobile (marked).
• Press the display key Options.
• Select Connect Mobile and press OK.

Bluetooth is activated on the base. The base connects to the mobile.

You can also assign this function to a function key on the base:

• Press and hold the display/function key until a list of possible key assignments is displayed.
• Select the function Connect Mobile and press OK.

If the mobile is taken beyond the Bluetooth range of the base, you should re-establish the connection between the two as soon as the mobile is within range again(see above). This will ensure that a GSM call either to the base or from the base using the GSM connection is transferred.

You can conduct calls on your base and/or a registered handset via the GSM connection on your Bluetooth GSM mobile (calls external parties via the GSM connection on the mobile or accept calls via the GSM connection) if the following prerequisites are met:

• Bluetooth mode is activated on the base and mobile.
• Your GSM mobile has been registered on the base and activated.
• There is a Bluetooth connection established between the base and mobile.
• The mobile is in range of the base (less than 10 m).
• For outgoing calls: The mobile connection is assigned to the base as a send connection, or the base can select the GSM connection as a send connection.
• For accepting incoming calls: The GSM connection is assigned to the base as a receive connection.

Prerequisite: At least one mobile is in the list of known devices or a mobile is temporarily connected to the base.

Open Menu – Settings – Telephony - Send Connections

A list of internal parties is displayed (base, handsets, answering machine).

• Select the internal party to be assigned to the GSM connection as a receive connection and press the display key OK.
• Select Yes if the selected connection should continue to be the receive connection for the internal party.
• Select No if it should not be the receive connection.
• Switch to the GSM connection.
• Select Yes if the GSM connection should be the receive connection for the internal party.
• Press the display key Save to save the changes.

Prerequisite: Several phone numbers are configured for your desktop phone.

Open Menu – Settings – Telephony - Send Connections

A list of the internal parties (desktop phone, handsets, fax machine INT8 – where connected) is displayed.

• Select the internal parties that should be assigned a new send connection and press the display key OK.
• Select at each call or select a connection as the send connection.
• Press the display key Save to save the changes.

If you select Select at each call, the internal party can select which send connection is used to establish a connection every time he makes a call.

Before you can use your Bluetooth devices, you must first activate Bluetooth and then
register the devices to the desktop phone. To use the phone numbers, dialing codes
(country and area code) must be stored on the desktop phone.

Activating/deactivating Bluetooth mode

• Menu
• Bluetooth
• Activation
• Select and press OK to activate or deactivate Bluetooth mode

When the desktop phone is in idle status, the icon in the header indicates that Bluetooth mode is activated. As soon as Bluetooth is activated, your desktop phone is visible to all Bluetooth devices
in the receiving range and can communicate with all of the devices included in the Known Devices list.

Registering Bluetooth devices
The distance between the desktop phone in Bluetooth mode and the activated Bluetooth device (headset or data device) should be no more than 10 m.

• Menu
• Bluetooth
• Search for Headset / Search for Mobile phone / Search for Data Device

The search can take up to 30 seconds. Once the device has been found, its name or address is shown on the display.

• Press the display key “Options”.
• Trust Device
• Select and press OK.
• Enter the PIN of the Bluetooth device to be registered and press OK.

Generally you can enter a PIN of your choice for a data device. Subsequently, you must enter this PIN in the data device, too. Enter the preset PIN for the headset (usually:0000). For further information, please refer to the headset user guide. The device is saved in the list of known devices.

Please note:

You can operate headsets on your handset that have the headset or handsfree profile. If both profiles are available, the handsfree profile is used to communicate.

It can take up to five seconds to establish a connection between your desktop phone and a Bluetooth headset. This applies both when a call is accepted using the headset or transferred to the headset, and when a number is dialed from the headset.

If you would like to use a headset already registered to another device (e.g., to a mobile phone) with your desktop phone, please deactivate this connection before you start the registration process.
The known devices list can only contain one Bluetooth headset. If you register a second headset, the first one is deleted from the list.
If the list already contains six entries, the last device to be entered is deleted during the subsequent registration process.
Exception: The headset entry is only overwritten by a new headset and a headset only overwrites the headset entry.

By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

- You have not ordered CID from your network provider or
- Your telephone is connected through a PBX that does not transmit all information.

Is your telephone connected through a PBX/gateway?
You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
In most cases, simply resetting this device will remedy the situation:
- Briefly disconnect the power plug of your PBX.
- Re-insert the plug and wait for the device to restart.

If the caller number is still not displayed:
Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

Have you ordered the CID service from your network provider?
Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

- You have not ordered CID from your network provider or
- Your telephone is connected through a PBX that does not transmit all information.

Is your telephone connected through a PBX/gateway?
You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
In most cases, simply resetting this device will remedy the situation:
- Briefly disconnect the power plug of your PBX.
- Re-insert the plug and wait for the device to restart.

If the caller number is still not displayed:
Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

Have you ordered the CID service from your network provider?
Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:

• Use the phone cable from the Gigaset packaging.
• If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
• Connect the cable to the router`s phone jack / phone port / FON port.
• Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
• Please make sure that your internet connection is working.

If the problem persists, please contact your provider.

Eine mögliche Ursache ist, dass Anrufe ins Ausland in den Einstellungen des verwendeten Routers deaktiviert sind.

Beispiel Router AVM Fritz!Box:

In den Einstellungen der AVM Fritz!Box unter Telefonie - eigene Rufnummern - Sicherheit - Auswahl ändern besteht die Möglichkeit Anrufe ins Ausland für angeschlossene IP-Telefone zu erlauben bzw. nicht zu erlauben.

To change back the language follow the following procedure:

• Base in idle mode.
• Open menu
  
• Enter 9 5
• Select your language
  

Yes, with the Dialling Plans. You can make fixe line calls via Provider A and calls to mobile phones via provider B.

Yes, up to 6.

The configuration can be done with the Web Configurator. Under “Settings” – “Telephony” – “Number assignment” you can configure the send – and receive numbers.

The configuration can be done with the Web Configurator. Under “Settings” – “Telephony” – “Number assignment” you can configure the send – and receive numbers.

In the WebGUI open the Settings - Management - Save & Restore Web page.

In the Save device settings to PC area:

Click the Save button next to Save settings.

The desktop phone will create a file Gigaset-yyyy-mm-dd.cfg (default name;

yyyy = year 4-digit format, mm = month 2-digit, dd = day 2-digit) with the

configuration data.

A browser-specific dialogue box appears where you can open/save the file.

Change the name, if necessary, and save the file on your PC.

The file will then contain e.g.:

• The settings for the local network (IP configuration),
• The active MSNs/connections,
• The assignment of send and receive connections,
• Your own local area code and access code,
• Network mailbox number,
• The info services settings,
• The settings for synchronisation with a time server,
• The ECO DECT settings,
• The settings for ringer melodies and volume levels

If you change the settings accidentally or you need to reset the desktop phone due

to a fault, you can reload the saved settings from the file on your PC to your phone.

Open the Settings - Management - Save & Restore Web page.

For some VoIP accounts/providers it might be necessary to adjust the volume for the dive via the Web Configurator. To do this, please open on your computer the Web Configurator and setup the VoIP Volume under “Settings” – Telephony” – “Audio” – “VoIP Volume”.

Yes, with the Dialling Plans. You can make fixe line calls via Provider A and calls to mobile phones via provider B.

Yes, the device checks the connection in fix timeframes. Without phone calls the device needs a data volume of approximately 70 MByte per month

Functions to improve the voice quality on VoIP connections are available on the Web configuration page: Settings - Telephony - Audio

The voice quality for VoIP connections is mainly determined by the voice codec used for transferring the data and the available bandwidth of your DSL connection.

In the case of the voice codec, the voice data is digitalised (coded/decoded) and compressed. A "better" codec (better voice quality) means more data needs to be transferred, i.e., perfect voice data transfer requires a DSL connection with a larger bandwidth.

You can influence the voice quality by selecting (bearing in mind the bandwidth of your DSL connection) the voice codecs your phone is to use, and specifying the order in which the codecs are to be suggested when a VoIP connection is established.

Default settings for the codecs used are stored in your phone; one setting optimised for low bandwidths and one for high bandwidths.

You can generally select one of these standard settings for all VoIP connections on your phone. If your DSL connection has a low bandwidth, you can also exclude parallel VoIP connection to increase the voice quality.

You can also make the settings for the voice codecs yourself by selecting the voice codecs to be used for each VoIP connection on your phone and specifying the sequence in which they should be suggested when establishing a VoIP connection.

The following voice codecs are supported by your phone:

G.722

Excellent voice quality. The broadband speech codec G.722 works at the same bit rate as G.711 (64 kbit/s per speech connection) but with a higher sampling rate. This allows higher frequencies to be played back. The speech tone is therefore clearer and better than for the other codecs (High Definition Sound Performance).

G.711 a law / G.711 μ law

Excellent voice quality (comparable with ISDN). The necessary bandwidth is 64 kbit/s per voice connection.

G.726

Good voice quality (inferior to that with G.711 but better than with G.729). Your phone supports G726 with a transmission rate of 32 kbit/s per voice connection.

G.729

Average voice quality. The necessary bandwidth is less than or equal to 8 kbit/s per voice connection. To save additional bandwidth and transmission capacity, on VoIP connections that use the G.729 codec you can suppress the transmission of voice packets in pauses ("Silence Suppression"). Instead of the background noises in your environment, your caller then hears a synthetic noise generated in the receiver (option: Enable Annex B for codec G.729).

Observe the following for good voice quality:

• When making calls using VoIP, avoid performing other Internet activities (e.g., surfing the Internet).
• Please note that voice delays can occur depending on the codec used and the network capacity utilisation.

It depends on the type of compression. The bandwidth for Voice over IP is between 12 and 80 KBit/s. Please note that these values are theoretical. For practice: As much bandwidth as possible.

Eine mögliche Ursache ist, dass Anrufe ins Ausland in den Einstellungen des verwendeten Routers deaktiviert sind.

Beispiel Router AVM Fritz!Box:

In den Einstellungen der AVM Fritz!Box unter Telefonie - eigene Rufnummern - Sicherheit - Auswahl ändern besteht die Möglichkeit Anrufe ins Ausland für angeschlossene IP-Telefone zu erlauben bzw. nicht zu erlauben.

The following voice codecs are supported by your phone:

G.722

Excellent voice quality. The broadband speech codec G.722 works at the same

bit rate as G.711 (64 kbit/s per speech connection) but with a higher sampling

rate. This allows higher frequencies to be played back. The speech tone is therefore

clearer and better than for the other codecs (High Definition Sound Performance).

G.711 a law / G.711 μ law

Excellent voice quality (comparable with ISDN). The necessary bandwidth is

64 kbit/s per voice connection.

G.726

Good voice quality (inferior to that with G.711 but better than with G.729).

Your phone supports G726 with a transmission rate of 32 kbit/s per voice

connection.

G.729

Average voice quality. The necessary bandwidth is less than or equal to 8 kbit/s

per voice connection.

To save additional bandwidth and transmission capacity, on VoIP connections

that use the G.729 codec you can suppress the transmission of voice packets in

pauses ("Silence Suppression"). Instead of the background noises in your environment,

your caller then hears a synthetic noise generated in the receiver

(option: Enable Annex B for codec G.729).

If you wish to permit two VoIP connections, do the following steps: 

• Open the Web Configurator
• Open the menu "Settings" - "Telephony" - "Audio"
• Activate the option "No" next to "Allow 1 VoIP call only"

Please Note: If, however, your DSL connection has a narrow bandwidth, there may be problems if two VoIP calls are made at the same time.The data is no longer transferred properly(long voice delay, datalosses etc.).

The echo effect is based on network switches.

Default data server “gigaset.com/chagall” doesn’t work anymore and must be replaced with “profile.gigaset.net/device” over WEB UI under Settings - Management – Firmware Update.

If you wish to permit two VoIP connections, do the following steps: 

• Open the Web Configurator
• Open the menu "Settings" - "Telephony" - "Audio"
• Activate the option "No" next to "Allow 1 VoIP call only"

Please Note: If, however, your DSL connection has a narrow bandwidth, there may be problems if two VoIP calls are made at the same time.The data is no longer transferred properly(long voice delay, datalosses etc.).

Prerequisites: A standard Web browser is installed on the PC e.g., Internet Explorer version 6.0 or higher, or Firefox version 1.0.4 or higher. The phone and PC are directly connected with each other via a router. The settings of any existing firewall installed on your PC allow the PC and phone to communicate with each other.

There are two ways of connecting your PC to the Web configurator on the Gigaset:

1. Via the phone's IP address in the local network

Establish the current IP address of the phone. It is displayed when you open the following menu:

• Menu-Settings-System-Local Network (enter PIN)

Your phone's IP address can change if you have activated dynamic IP address Assignment

• Launch the Web browser on your PC.

• Enter http:// and the telephone's current IP address (for example:http://192.168.2.2) into the address field of the Web browser.

• Press the return key.

A connection is established to the phone's Web configurator.

Warning:
If one of the four parts of the IP address contains leading zeros (e.g., 002), these zeros must not be entered in the Web browser address field. Otherwise, the Web browser will not be able to establish a connection to the Web configurator.
Example: The IP address 192.168.002.002 is displayed on the phone. 192.168.2.2 should be entered in the address field.

2. Via the Gigaset configuration service, if the phone and PC are connected to the Internet

Prerequisite: Your PC and phone are connected to the Internet.

• Launch the Web browser on your PC.
• Enter one of the following URLs into the Web browser's address field:

www.gigaset-config.com
www.gigaset-device.com

• Press the return key.

You will receive a message stating that the connection has been forwarded to phone.
If several Gigaset phones can be reached via your Internet connection, you are asked which of these phones you would like to be connected to.
After successfully forwarding the connection, the Web configurator's Login page is displayed in the Web browser.

Please note:
The connection between the PC and the Web configurator is a local connection (LAN connection). The Internet is only accessed to establish the connection.